Immediate Availability
Two (2) Nozzle Spray Dryers and following
equipment from an organic dyestuff plant in USA
Previous owner Crompton and Knowles Inc.


1. Anhydro Tall form Nozzle spray dryer in Stainless Steel type III AK No. 74 TF supplied by APV Crepaco

Unit still installed and complete with structure, instruments, CIP system, ductwork, cyclone collector, rotary valve, exhaust fan, wet scrubber and exhaust stack.  Total Height 90ft inclusive of about 40ft drying chamber, diameter of feed chamber 30 ft, heating by direct combustion natural gas fired heater, dryer equipped with nozzle atomizers.  Feed Chamber 316 SS, Drying Chamber and ductwork 304 SS with internal 2B finish and all welds ground smooth

Specification:
Feed solids 40%
Feed rate 1790 Lbs/Hour
Water evaporation Capacity 1225 lbs/hour
Powder production 566 Lbs/hour
Inlet air temp 465 degree F
Outlet air temp at 250 degree F
Moisture in powder: less than 5%

2. Bayliss tower-nozzle spray dryer in Stainless Steel supplied by Komline Sanderson

Unit still installed and complete with structure, instruments, CIP system, ductwork, cyclone collector, rotary valve, exhaust fan, wet scrubber and exhaust stack, Total height 50 ft, 12 ft Dia chamber, equipped with Nozzle atomizers

Specification:
Feed solids 35%
Feed rate 1580 Lbs/Hour
Water evaporation Capacity 1015 lbs/hour
Powder production 565 Lbs/hour
Inlet air temp 430 degree F
Outlet air temp at 250 degree F
Moisture in powder: less than 3%



List of other Equipment:

1.One (1) Premier Mill, model HML1.5, Pilot Plant Supermill, 5hp, mechanical seal, serial no. MML90940-90-0183, pump motor 0.33hp, 3 phase, 60HZ, 230V, 1996

2.One (1) Cowles Dissolver, stainless steel, Model VHLM5, 3600rpm, serial no. LA626, air over oil lift, with 20 gallon SS mixing pot on wheels, 3 phase, 60HZ, 230/460 V, 1996

3.One (1) heat exchanger, graphite block, Kearney, 75psi and 360 degF both sides, serial no 7735, 1984

4. Universal Wear Testers, Custom Scientific Instruments.- Two (2) Available

5.One (1) Nauta Mixer, approx 150 ft3, JH Day, 304 SS, 8 ft diameter x 12 ft, serial no 86-12, dual motor 15HP/2HP, single screw

6.One (1) 175 ft3 Ribbon Blender, 304SS, jacketed, 4.5 ft wide x 12 ft long x 5 ft deep, double ribbon, center bottom outlet,  cover with 3 hatches, chain/sprocket driven, approx 50hp drive.

7.One (1) 175 ft3 Ribbon Blender, 304SS, 4.5 ft wide x 12 ft long x 5 ft deep, double ribbon, center bottom outlet, cover with 3 hatches, chain/sprocket driven, approx 50hp drive.

8.One (1) Bauermeister Universal Mill, model UT13, serial no 8655, 20hp, 3520rpm, with Farr dust collector and discharge conveyor, skid mounted on top of a Nauta Mixer.

9.One (1) 4000 gallon 316SS Reactor, Cryochem, 8 ft Dia. x 10 ft straight side, Inconnel 600 dimple jacket, 75psi and 300 degF internal, 150psi and 300 deg F in jacket, NB no. 788, Chemineer drive, model no 5HTN-15, dual hp 15/6.7, 56/37.3 output rpm, dual paddle agitator, (4) baffles, lug mounted.

10. Filter Presses, (62) recessed plates, polypropylene, 4 eye, 1200mm Lenser plates, Shriver skeleton, hydraulic closure- Two (2) Available


11.One (1) 20 gallon NICKEL Reactor, Baeurle & Morris, 500 psi at 450 deg F internal, 150 psi at 450 degF in jacket, shell 0.5 inch thick, 1.5 ft Dia. x 2.0 ft straight side, full steel jacket, NB no 1338,  serial no 25954, Philadelphia drive, model PMG-A6-11, pneumatic driven, mechanical seal, on legs, 1985.

                                                                           
INDUSTRIAL ASSET MANAGEMENT LLC
1450 Parkside Avenue
Suite 27,Ewing
New Jersey 08638- 2948
USA
+1-609-936-8696
fax +1-609-936-9102
This email address is being protected from spambots. You need JavaScript enabled to view it.
 

request more info.

Additional information